- 您現在的位置：買賣IC網 > PDF目錄354437 > MC33984 (Motorola, Inc.) Dual Intelligent High-Current Self-Protected Silicon High-Side Switch (4.0 mз) PDF資料下載
參數資料
| 型號： | MC33984 |
| 廠商： | Motorola, Inc. |
| 英文描述： | Dual Intelligent High-Current Self-Protected Silicon High-Side Switch (4.0 mз) |
| 中文描述： | 雙智能大電流的自我保護硅高邊開關（4.0mз） |
| 文件頁數： | 10/28頁 |
| 文件大小： | 492K |
| 代理商： | MC33984 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
33984
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
18
A logic [1] on bit D2 disables the overcurrent low (CD dis)
detection timeout feature. A logic [1] on bit D3 disables the open
load (OL) detection feature.
Address x100—Direct Input Control Register (DICR)
The DICR register is used by the MCU to enable, disable, or
configure the direct IN terminal control of each output. Each
output is independently selected for configuration based on the
state of bit D7. A write to this register when bit D7 is logic [0] will
configure the direct input control for the HS0. Similarly, if D7 is
logic [1] when this register is written, then HS1 is configured.
A logic [0] on bit D1 will enable the output for direct control by
the IN terminal. A logic [1] on bit D1 will disable the output from
direct control. While addressing this register, if the input was
enabled for direct control, a logic [1] for the D0 bit will result in
a Boolean AND of the IN terminal with its corresponding D0
message bit when addressing the OCR register. Similarly, a
logic [0] on the D0 terminal results in a Boolean OR of the IN
terminal with the corresponding message bits when addressing
the OCR register.
The DICR register is useful if there is a need to
independently turn on and off several loads that are PWM’d at
the same frequency and duty cycle with only one PWM signal.
This type of operation can be accomplished by connecting the
pertinent direct IN terminals of several devices to a PWM output
port from the MCU and configuring each of the outputs to be
controlled via their respective direct IN terminal. The DICR is
then used to Boolean AND the direct IN(s) of each of the
outputs with the dedicated SPI bit that also controls the output.
Each configured SPI bit can now be used to enable and disable
the common PWM signal from controlling its assigned output.
A logic [1] on bit D2 is used to select the high ratio (CSR1,
1/41000) on the CSNS terminal for the selected output. The
default value [0] is used to select the low ratio (CSR0, 1/20500).
A logic [1] on bit D3 is used to select the high speed slew rate
for the selected output. The default value [0] corresponds to the
low speed slew rate.
Address 0101—Output Switching Delay Register (OSDR)
The OSDR register configures the device with a
programmable time delay that is active during Output ON
transitions initiated via SPI (not via direct input).
A write to this register configures both outputs for different
delay. Whenever the input is commanded to transition from
logic [0] to logic [1], both outputs will be held OFF for the time
delay configured in the OSDR. The programming of the
contents of this register have no effect on device fail-safe mode
operation. The default value of the OSDR register is 000,
equating to no delay. This feature allows the user a way to
minimize inrush currents, or surges, thereby allowing loads to
be switched ON with a single command. There are eight
selectable output switching delay times that range from 0 ms to
525 ms (refer to Table 6).
Address 1101—Watchdog Register (WDR)
The WDR register is used by the MCU to configure the
watchdog timeout. Watchdog timeout is configured using bits
D1:D0. When D1:D0 bits are programmed for the desired
watchdog timeout period, the WD bit (D7) should be toggled as
well, ensuring the new timeout period is programmed at the
beginning of a new count sequence (refer to Table 7).
Address 0110—No Action Register (NAR)
The NAR register can be used to no-operation fill SPI data
packets in a daisy chain SPI configuration. This allows devices
to not be affected by commands being clocked over a daisy-
chained SPI configuration, and by toggling the WD bit (D7), the
watchdog circuitry will continue to be reset while no
programming or data readback functions are being requested
from the device.
Table 5. Overcurrent Low Detection
Blanking Time
OCLT[1:0]
Timing
00
155 ms
01
10 ms
10
1.2 ms
11
150
s
Table 6. Switching Delay
OSD[2:0] (D2:D0)
Turn ON Delay (ms)
HS0
Turn ON Delay (ms)
HS1
000
0
001
75
0
010
150
011
225
150
100
300
101
375
300
110
450
111
525
450
Table 7. Watchdog Timeout
WD[1:0] (D1:D0)
Timing (ms)
00
620
01
310
10
2500
11
1250
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33689 | Single Output LDO, 400mA, Fixed(2.85V), Low Noise, Fast Transient Response 8-MSOP -40 to 85 |
| MC33689DWB | Single Output LDO, 400mA, Fixed(2.85V), Low Noise, Fast Transient Response 8-MSOP -40 to 85 |
| MC100LVEL39 | Replaced by TPS2051B : 0.7A, 2.7-5.5V Single Hi-Side MOSFET, Fault Report, Act-High Enable 8-SOIC 0 to 85 |
| MC100LVEL39DW | Single, Current-Limited, Power-Distribution Switch 5-SOT-23 -40 to 85 |
| MC74LVQ08D | Enhanced Low Input (2.25V-5.5V) up to 1MHz Frequency, Sync. Buck Controller, source only 16-HTSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33984BPNA | 功能描述:電源開關 IC - 配電 SPD4 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33984BPNAR2 | 功能描述:電源開關 IC - 配電 SPD4 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33984CHFK | 功能描述:電源開關 IC - 配電 Dual 4mOhms smart RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33984CHFKR2 | 功能描述:電源開關 IC - 配電 Dual 4mOhms smart RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33984PNA | 制造商:Freescale Semiconductor 功能描述:POWER SWITCH HI SIDE 30A 16-PIN QFN - Trays |
發布緊急采購，3分鐘左右您將得到回復。